Semi-trailer truck pre-trip inspection

Any semi-trailer truck pre-trip inspection should be based on the CDL Vehicle Inspection Test‎‎.

Versions

According to the 11.6.1 section of the CDL Vehicle Inspection Test‎‎, the tested applicant is "required to perform one of the four versions of a Vehicle inspection in the vehicle."

All versions include:

1. an engine start,
2. an in-cab inspection,
3. an inspection of the coupling system,
4. an inspection of the entire vehicle or only a portion of the vehicle.

Version A

1. Front of truck
2. Engine compartment
3. Steering components
4. Of one side of the steering axle:
   • Suspension components
   • Brake components
   • Tires
   • Wheels
5. Coupling system
6. Inside the cab, including Air brake check, Parking brake check, Service brake check

Version B

1. Driver's door/fuel area
2. Behind the cab
3. Of one side of any tractor tandem axles:
   • Suspension components
   • Brake components
   • Tires
   • Wheels
4. Coupling system
5. Inside the cab, including Air brake check, Parking brake check, Service brake check

Version C

1. Coupling system
2. Trailer front and sides
3. Of one side of any trailer tandem axles:
   • Suspension components
   • Brake components
   • Tires
   • Wheels
4. Trailer rear
5. Inside the cab, including Air brake check, Parking brake check, Service brake check

Full version

An inspection of the entire vehicle may consist of:

1. Front of truck
2. Engine compartment
3. Steering components
4. Of one side of any axle:
   • Suspension components
   • Brake components
   • Tires
   • Wheels
5. Driver's door/fuel area
6. Behind the cab
7. Coupling system
8. Trailer front and sides
9. Trailer rear
10. Inside the cab, including Air brake check, Parking brake check, Service brake check

Front of truck

Front lights

The headlights, turn signals, and clearance lights:

1. Meet general requirements.
2. Are clean.
3. Are the proper color.

Front leaks

No leaks or puddles from dripping fluids under the engine or transmission.

Engine compartment

DPF

Mounting brackets, hoses, and electrical components of the diesel particulate filter (DPF) meet:

1. General requirements.
2. Requirements for fluid-containing items.

Engine hoses

Engine hoses must meet the Requirements for fluid-containing items.

Coolant level

The coolant level must be at the proper level as observed from the reservoir tank or sight glass.

Water pump

The tested person is supposed to identify whether the pump is belt-driven or gear-driven. Any belt-driven pump must meet the Requirements for engine compartment belts. Any water pump must also meet:

1. General requirements.
2. Requirements for fluid-containing items.

Inside the cab

Brake check series

The brake check series consists of three different checks:

1. Air brake check
2. Parking brake check
3. Service brake check

Air brake check

Failure to perform all three components of the air brake check correctly will result in an automatic failure of thee vehicle inspection test. If you realize that you have missed something or did something incorrectly during your air brake check, you may start over.

Requirements

Engine compartment belts

Engine compartment belts may include power steering belt, water pump belt, alternator belt, and/or air compressor belt. During the inspection, they must:

1. Be checked for snugness (1/2 to 3/4 inch play at center of belt), cracks, frays, loose fibers or signs of wear.
2. Not be damaged or missing, be mounted securely and operating properly.

Fluid-containing items

Any inspected item that contains any fluid must be not dry-cracked, loose or leaking.

General

Any inspected item and its component or part must be:

• If the item should:
  1. Not be movable, then, securely mounted,.
  2. Be movable, then, fastened or not loose.
• Not broken, cracked, damaged, or missing.